Please select To the mobile version | Continue to access the desktop computer version

Electronic Engineer Discuss

12Next
Return to list New
View: 24518|Reply: 19

The dso5102p does not turn on at all.

[Copy link]

1

Threads

5

Posts

5

Credits

新手上路

Rank: 1

Credits
5
Post time 2017-8-9 21:40:41 | Show all posts |Read mode
Edited by Rexdn at 2017-8-9 21:43

Helo.
I bought an oscilloscope on Ali. But it does not work at all!
The seller does not accept it back. I want to repair it.
The oscilloscope does not turn on at all.
All voltages on the power supply are OK.
Please see the video.
https://yadi.sk/i/W7QA1fpO3LcFew
Thanks in advance


Reply

Use magic Report

167

Threads

2070

Posts

2232

Credits

版主

Rank: 7Rank: 7Rank: 7

Credits
2232
Post time 2017-8-10 09:05:18 | Show all posts
Sir, please check the voltages of the power supply board in the scope as the following picture:


And tell me the results.

This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

1

Threads

5

Posts

5

Credits

新手上路

Rank: 1

Credits
5
 Author| Post time 2017-8-10 19:24:00 | Show all posts
Hello, I measured the voltage.
I think everything is OK

This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

1

Threads

5

Posts

5

Credits

新手上路

Rank: 1

Credits
5
 Author| Post time 2017-8-11 02:48:41 | Show all posts
Edited by Rexdn at 2017-8-11 03:00

I read your message board and assembled the TTL-RS232 circuit

Then launched SecureCRT.
It is visible, I turned on and off the oscilloscope 2 times.
The terminal displays only two characters "O" & "M"

My e-mail - rexdn2@rambler.ru









This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

167

Threads

2070

Posts

2232

Credits

版主

Rank: 7Rank: 7Rank: 7

Credits
2232
Post time 2017-8-11 14:43:04 | Show all posts
Sir, please exchange RX and TX connectors to try.

1

Threads

5

Posts

5

Credits

新手上路

Rank: 1

Credits
5
 Author| Post time 2017-8-14 03:53:41 | Show all posts
Edited by Rexdn at 2017-8-14 04:01

Please watch the video. Length - 4 minutes  https://yadi.sk/i/P9JXtngI3LxNQU
The oscilloscope does not work.
Where I made a mistake?I tested it with different SD.
Probably this is not software, but hardware failure?
Please watch the video.
P.S. The connection of RX and TX is correct. Otherwise nothing works at all.









1

Threads

5

Posts

5

Credits

新手上路

Rank: 1

Credits
5
 Author| Post time 2017-8-17 16:37:47 | Show all posts
Edited by Rexdn at 2017-8-17 16:41

Well, if I replace K9F1G08U0E, can I program the oscilloscope with a SD card?
I'll put an empty chip and program it with an oscilloscope and SD card. Is this possible?



167

Threads

2070

Posts

2232

Credits

版主

Rank: 7Rank: 7Rank: 7

Credits
2232
Post time 2017-8-19 08:47:20 | Show all posts
Sir, yes, you can program the new chip K9F1G08U0E with SD card.

0

Threads

15

Posts

15

Credits

新手上路

Rank: 1

Credits
15
Post time 2017-9-8 22:08:05 | Show all posts
Edited by kalebevando at 2017-9-8 22:14
Rexdn replied at 2017-8-11 02:48
I read your message board and assembled the TTL-RS232 circuit

Then launched SecureCRT.

The same result as my. It is as if ... No information was recorded in the Nand memory of the oscilloscope.
I have tried with SecureCRT, with PuTTy, with TeraTerm and the result is always the same, no information is shown on the PC screen.
Either we do not know how to use the program, or it's what I'm imagining (all oscilloscope data has been erased from memory).
Anyone who knows how to use these programs could post a video showing how to configure and use SecureCRT connected on an oscilloscope?

O mesmo resultado do meu. ? como se... Nenhuma informa??o estivesse gravado na memoria Nand do osciloscopio.
Eu já tentei com o SecureCRT, com o PuTTy, com o TeraTerm e o resultado é sempre o mesmo, nenhuma informa??o é mostrada na tela do PC.
Ou n?o estamos sabendo usar o programa, ou é aquilo que eu estou imaginando ( todos os dados do osciloscopio foi apagados da memoria ).
Alguém que sabe usar esses programas poderia postar um video mostrando como se configura e usa o SecureCRT conectado em um osciloscopio?

167

Threads

2070

Posts

2232

Credits

版主

Rank: 7Rank: 7Rank: 7

Credits
2232
Post time 2017-9-12 10:16:12 | Show all posts
Sir, sorry, we can't make a clear judgement about where the problem is.
Please contact your seller to return factory for repair.
12Next
Return to list New
You have to log in before you can reply Login | Register

Points Rules

Dark room|Mobile|Archiver|Electronic Engineer Discuss

2024-3-29 23:10 GMT+8 , Processed in 0.172478 second(s), 22 queries .

Powered by Discuz! X3.2

© 2001-2013 Comsenz Inc.

Quick Reply To Top Return to the list