Hantek HDM3065B, SCPI commands

CYH2018

Hello, I've some problems on the SCPI commands of a Hantek HDM3065B.

I've tried the forum 'www.eediscuss.com' but it is impossible to register, the confirmation email is not sent, I've checked the junk folder, no email after 3 days.

The commands 'R?' and 'DATA:REMove?' do not work, I get the error '-113, undefined header'.
The command 'TRIGEL:AUTO OFF' seems to randomly toggle the delay auto on and off.
With delay auto off, the command 'TRIGEL 0' does not change the delay to zero.

I've tried the SCPI modes 'Default', 'Agilent' and 'Keithley', the results are the same.
The other commands I've tried work correctly.

What I'm trying to do is continuously read values of current from the multi-meter at maximum speed, this to compute the total current consumption. Is there a way to do it?

Is there a firmware update for this multi-meter HDM3065B?

Thank you,

CYH2018

Dear Sir,

Greeting from Hantek.

Where did you get these SCPI commands? The SCPI commands you mentioned is not included in our HDM3000_SCPI Programming Reference documents.
Please download the SCPI Programming Reference document as follow:
http://www.hantek.com/products/detail/16176

Have a nice day.

Tecno

Hello Candy,

thank you for helping me creating an account in this forum.

I've downloaded 'HantekHDM3000-2021042920210429120417.rar' from you link, inside it there is 'HDM3000_SCPI 编程参考_Ver 1.01.pdf' which unfortunately is only in Chinese, and it seems incomplete, many commands, which I've tested to work on HDM3065B, are not present or barely mentioned in this guide, for example:
*IDN?
*RST
INIT
FETC?
READ?
TRIG:SOUR IMM
...

So I still have many question on how to program this multimeter by SCPI:
- how do I read a block measures and remove them from the buffer? (the standard command is 'R?')
- how do I disable the auto delay? (the standard command is 'TRIG: DEL:AUTO OFF')
- how do I change the delay to zero? (the standard command is 'TRIG: DEL 0')
- is there an update for this multimeter? I've checked here http://www.hantek.com/download?key=zxgj&sid=3018&pid=0&word= is it the right place?

Sorry for all these questions and thank you,
Gabriele

Tecno

Hello, can anybody from Hantek please respond to my questions above?

Jing

Tecno replied at 2022-12-27 21:28
Hello, can anybody from Hantek please respond to my questions above?

Dear Sir，
The English version of SCPI instruction manual has been sent, please pay attention to check.

Tecno

Dear Sir Jing, where can I find documentation for the TRIG instructions?
Thank you.

Jing

Tecno replied at 2022-12-28 17:03
Dear Sir Jing, where can I find documentation for the TRIG instructions?
Thank you.

Dear Sir，
3065 All instructions are all in the document, there are no other instructions.

Tecno

Sorry to insist, but not all instructions are fully documented. For example at page 57 of your document I read:

The instrument will clear all measurements from the reading memory when the
measurement configuration changes, or when any of the following commands are
executed: INITiate, MEASure:<function>?, READ?, *RST, SYSTem: PRESet.

But I can't find any explanation on any of these commands. For example, what are the options of the "MEASure:<function>?" command ? What values does <function> accept? And all these commands work, so they are implemented in the HDM3065B.
They are generic SCPI commands and I can find a good explanation in the "HP 34401A" manual, but the commands of the "TRIG" session does not work as intended.

Is there a way to change the trigger delay by using the SCPI commands like any other HP/Agilent multimeter?