Please select To the mobile version | Continue to access the desktop computer version

Electronic Engineer Discuss

12Next
Return to list New
View: 12351|Reply: 19

DSO 2D10 Issue with higher memory depth

[Copy link]

1

Threads

10

Posts

10

Credits

新手上路

Rank: 1

Credits
10
Post time 2022-1-4 04:00:18 | Show all posts |Read mode
Edited by masta-k74 at 2022-1-5 04:22

My brand new 2D10 shows a strange "interference signal" when the memory depth is set to more than 40k. The interference signal always appears with a time delay after increasing the memory depth and overlays the measurement signal. (Many, very short spikes on the screen) It also appears without any probes connected. Can I regard this behaviour as another bug or is there possibly a hardware defect?
I have already tested different software and Firmware versions. (At this moment, the actual Firmware from December 30. 2021 is installed, it doesn't help...)
Here a video of this issue.
https://1drv.ms/v/s!AiPaG0Dlc3q2gZZ0pJNZPpmzM4aY8g?e=anox9T








Reply

Use magic Report

0

Threads

5

Posts

5

Credits

新手上路

Rank: 1

Credits
5
Post time 2022-1-7 01:15:55 | Show all posts
Unfortunately I have the same issue on my 2D10 I received just a couple of days ago from Banggood.
Displaying signal at 4k and 40k points works OK, but when I go higher in memory settings, the scope starts behaving badly.
Memory settings 400k, 4M and 8M are unusable.
This happens almost instantly when I change the Volts/div setting, zooming in on the signal.
If I switch it OFF and ON again, the problem comes back by adjusting V/div.
The problem exist also in GND coupled mode or even the probe disconnected with no signal at all.
Serial: CN21350290127xx
SW: 20210726
HW: 3.2.1.0.0.0.0.1
FW: 3202
I have since tried the latest SW from the Hantek site 20211230, it behaves the same.
I hope Hantek will reply, I'd like to know if it is a hardware or software defect and can we expect a fix?
My video of the problem is available here:
https://www.youtube.com/watch?v=gFO4QoYVsSE

0

Threads

1

Posts

1

Credits

新手上路

Rank: 1

Credits
1
Post time 2022-1-5 04:48:28 | Show all posts
Edited by naelolaiz at 2022-1-5 06:37

I have the same issue with a brand new 2D15. I also tested it with the provided firmware, and the latest one.
Here are my videos:
https://www.youtube.com/watch?v=7vd8mAi3oPI
https://www.youtube.com/watch?v=MJYGLvc7Mws

Edit: other issues on the device:First: the sine frequency does not match the frequency of the generator.  Or the generator is really that bad that makes a 0.6 Hz modulation? Second: a different type of noise appears at the end of the buffers acquiring at 40K.I don?t trust this device as a measurement/testing equipment as far as it is behaving. Is is expected to behave this bad? Are all these hardware or software/firmware issues?
video url: https://www.youtube.com/watch?v=186fGh3LLVw
                                                        
                                            




60

Threads

443

Posts

443

Credits

版主

Rank: 7Rank: 7Rank: 7

Credits
443
Post time 2022-1-7 11:57:07 | Show all posts
naelolaiz replied at 2022-1-5 04:48
I have the same issue with a brand new 2D15. I also tested it with the provided firmware, and the la ...

Thank you for your feedback. This problem has been reported to the engineer, and I will notify you when a new firmware is released.

1

Threads

10

Posts

10

Credits

新手上路

Rank: 1

Credits
10
 Author| Post time 2022-1-9 18:10:07 | Show all posts
wangshuang replied at 2022-1-7 11:57
Thank you for your feedback. This problem has been reported to the engineer, and I will notify you ...

I assume now that you are also assuming a firmware bug and not a hardware defect?

2

Threads

5

Posts

5

Credits

新手上路

Rank: 1

Credits
5
Post time 2022-1-13 01:31:56 | Show all posts
I have also faced a problems with Memory depth larger than 4k, but with FFT (spectre on negative frequencies...)
https://www.eediscuss.com/forum. ... id=15885&extra=
Have not got any reply on this topic though...

1

Threads

10

Posts

10

Credits

新手上路

Rank: 1

Credits
10
 Author| Post time 2022-1-21 13:52:38 | Show all posts
Edited by masta-k74 at 2022-1-21 13:54

There is a new Firmware (dso3kb_20220118.upk) on official Website

1

Threads

10

Posts

10

Credits

新手上路

Rank: 1

Credits
10
 Author| Post time 2022-1-26 03:27:42 | Show all posts
This problem still persists...

1

Threads

10

Posts

10

Credits

新手上路

Rank: 1

Credits
10
 Author| Post time 2022-2-3 20:32:05 | Show all posts
One could almost get the impression that nobody is interested. I am well on the way to turning my back on Hantek for good. At any rate, you can't call that customer service. If a solution to the problem is still being sought, it would be desirable that it is at least communicated.
Return shipping to China is out of the question for cost reasons. Shipping from Germany costs about ?100, half the price of the device. In addition, you can read here from others who have tried it that there are sometimes problems with customs. Then the device and the money would be gone.

0

Threads

5

Posts

5

Credits

新手上路

Rank: 1

Credits
5
Post time 2022-2-9 00:55:40 | Show all posts
Looks like there is no solution to this issue.
The only feedback we received is that the problem has been reported to the engineer.
Shall I return my scope and ask for refund?
12Next
Return to list New
You have to log in before you can reply Login | Register

Points Rules

Dark room|Mobile|Archiver|Electronic Engineer Discuss

2024-3-29 04:10 GMT+8 , Processed in 0.246549 second(s), 22 queries .

Powered by Discuz! X3.2

© 2001-2013 Comsenz Inc.

Quick Reply To Top Return to the list