Please select To the mobile version | Continue to access the desktop computer version

Electronic Engineer Discuss

Author: WisdomAugust

MPO6002EDU Series Oscilloscope Guide

[Copy link]

58

Threads

1253

Posts

1333

Credits

金牌会员

Rank: 6Rank: 6

Credits
1333
 Author| Post time 2020-12-15 08:27:55 | Show all posts
Utility Key -> Pass/Fail -> Output to DDS Softkey help information
When turning on the output to DDS, the scope is able to output a negative pulse train from the Gen Out terminal.

Utility Key -> Pass/Fail -> Return Softkey help information
Press this softkey to return to the previous menu.

Utility Key -> System Set Softkey help information
This key opens the System Setup Menu where you can turn on or off the sound, set network, edit time and date, and perform touch panel calibration.

Utility Key -> System Set -> Sound Softkey help information
Turn on or off the sound of pressing keys.

Utility Key -> System Set -> Network Softkey help information
Press this softkey to open the Network Setup Menu.



58

Threads

1253

Posts

1333

Credits

金牌会员

Rank: 6Rank: 6

Credits
1333
 Author| Post time 2021-1-4 09:39:12 | Show all posts
Edited by WisdomAugust at 2021-1-4 09:40

Utility Key -> System Set -> Network -> Network Softkey help information
Toggle the network type between eth0 and wlan0.

Utility Key -> System Set -> Network -> Status On/Off Softkey help information
Turn on or off the network status.

Utility Key -> System Set -> Network -> DHCP On/Off Softkey help information
Turn on or off DHCP (Dynamic Host Configuration Protocol).

Utility Key -> System Set -> Network -> Auto IP On/Off Softkey help information
Enable or disable the Auto IP.

Utility Key -> System Set -> Network -> Confirm Softkey help information
Confirm your settings of the network menu page one.

Utility Key -> System Set -> Network -> IP Add Softkey help information
Configure the IP address.

Utility Key -> System Set -> Network -> Subnet Mask Softkey help information
Configure the IP Subnet Mask.


58

Threads

1253

Posts

1333

Credits

金牌会员

Rank: 6Rank: 6

Credits
1333
 Author| Post time 2021-1-5 08:37:06 | Show all posts
Edited by WisdomAugust at 2021-1-5 08:38

Utility Key -> System Set -> Network -> Gateway Softkey help information
Configure Gateway.

Utility Key -> System Set -> Network -> DNS Softkey help information
Configure DNS (Domain Name System).

Utility Key -> System Set -> Network -> Confirm Softkey help information
Confirm your settings of the network menu page two.

Utility Key -> System Set -> Network -> Hotspot Softkey help information
Press this softkey to enable the Hotspot Settings. The scope will automatically search for available hot spots nearby.
And SSID and PSK become active to be set.

Utility Key -> System Set -> Network -> Scan Result Softkey help information
Display searched nearby Wi-Fi hotspots.

Utility Key -> System Set -> Network -> SSID Softkey help information
Configure SSID (Service Set Identifier).

Utility Key -> System Set -> Network -> PSK Softkey help information
Configure PSK (Pre Shared Key).

Utility Key -> System Set -> Network -> Confirm Softkey help information
Confirm your settings of the network menu page three.



58

Threads

1253

Posts

1333

Credits

金牌会员

Rank: 6Rank: 6

Credits
1333
 Author| Post time 2021-1-6 08:26:41 | Show all posts
Edited by WisdomAugust at 2021-1-6 08:28

Utility Key -> System Set -> Network -> Mac Add Softkey help information
Configure MAC address.

Utility Key -> System Set -> Network -> Service Softkey help information
Switch the network protocol between TCP (Transmission Control Protocol) and HTTP (HyperText Transfer Protocol).

Utility Key -> System Set -> Network -> Return Softkey help information
Press this softkey to return to the previous menu.

Utility Key -> System Set -> Date&Time Softkey help information
Press this softkey to enter the Time Setup Menu.

Utility Key -> System Set -> Date&Time -> Year Softkey help information
Press this softkey and turn V0 knob to adjust correct year.

Utility Key -> System Set -> Date&Time -> Month Softkey help information
Press this softkey and turn V0 knob to adjust correct month.

Utility Key -> System Set -> Date&Time -> Day Softkey help information
Press this softkey and turn V0 knob to adjust correct day.

Utility Key -> System Set -> Date&Time -> Hour Softkey help information
Press this softkey and turn V0 knob to adjust correct hour.

Utility Key -> System Set -> Date&Time -> Minute Softkey help information
Press this softkey and turn V0 knob to adjust correct minute.

Utility Key -> System Set -> Date&Time -> Second Softkey help information
Press this softkey and turn V0 knob to adjust correct second.

Utility Key -> System Set -> Date&Time -> Return Softkey help information
Press this softkey to return to the previous menu.



58

Threads

1253

Posts

1333

Credits

金牌会员

Rank: 6Rank: 6

Credits
1333
 Author| Post time 2021-1-8 08:22:26 | Show all posts
Utility Key -> System Set -> TP Cal Softkey help information
To perform calibration of the touch panel.

Utility Key -> System Set -> Return Softkey help information
Press this softkey to return to the previous menu.

Utility Key -> Self Cal Softkey help information
Running the self-calibration routine to optimize the signal path in scope for top measurement accuracy.
Allow the temperature of the scope to warm up and disconnect all inputs and outputs before performing the self-calibration.
Self-calibration can be run any time the operating the temperature of the scope changes by more than 5.

Utility Key -> Self Cal -> Self Cal Softkey help information
Press this softkey to begin the user's self-calibration.

Utility Key -> Self Cal -> Cancel Softkey help information
Press this softkey to exit the user's self-calibration mode.

Utility Key -> Self Cal -> Return Softkey help information
Press this softkey to return to the previous menu.



58

Threads

1253

Posts

1333

Credits

金牌会员

Rank: 6Rank: 6

Credits
1333
 Author| Post time 2021-1-11 08:15:41 | Show all posts
Utility Key -> History Wave Softkey help information
You can use the History Waveform Mode to scroll back in time to isolate anomalies or other waveform events.
It automatically saves all acquisitions until the scope's history buffer full and stopping the trigger and displaying
a list of previously captured waveforms.

Utility Key -> Hardware Self-Test Softkey help information
Perform the self-test (a series of internal procedures) to verify the scope is operating properly.

Utility Key -> Front-Panel Self-Test Softkey help information
Press this key to perform a front panel keys, knobs, LEDs, and display test.

Utility Key -> Potter Diagram Softkey help information
Turn on or off frequency response analysis (FRA).



58

Threads

1253

Posts

1333

Credits

金牌会员

Rank: 6Rank: 6

Credits
1333
 Author| Post time 2021-1-12 08:04:21 | Show all posts
Edited by WisdomAugust at 2021-1-12 08:05

Utility Key -> Potter Diagram -> Enable Softkey help information
Press this softkey to display the Frequency Response Analysis chart.

Utility Key -> Potter Diagram -> SetUp Softkey help information
Enter the test parameters settings menu to set up source, frequency, and amplitude.

Utility Key -> Potter Diagram -> SetUp -> Input Source Softkey help information
Select the input source channel.

Utility Key -> Potter Diagram -> SetUp -> Output Source Softkey help information
Select the output source channel.

Utility Key -> Potter Diagram -> SetUp -> Freq Start Softkey help information
Set up the start frequency.

Utility Key -> Potter Diagram -> SetUp -> Freq Stop Softkey help information
Set up the stop frequency.

Utility Key -> Potter Diagram -> SetUp -> Amplitude Softkey help information
Set up the amplitude of the waveform generator.
Press this softkey to toggle between amplitude fine and amplitude coarse. And use V0 knob to adjust
the waveform generators amplitude.

Utility Key -> Potter Diagram -> SetUp -> Return Softkey help information
Press this softkey to return to the previous menu.



58

Threads

1253

Posts

1333

Credits

金牌会员

Rank: 6Rank: 6

Credits
1333
 Author| Post time 2021-1-13 13:32:41 | Show all posts
Utility Key -> Potter Diagram -> Chart Softkey help information
Display the test parameters settings menu to set up the gain and phase.

Utility Key -> Potter Diagram -> Chart -> Gain Scale Softkey help information
Press this softkey and turn V0 knob to adjust the gain scale (dB).

Utility Key -> Potter Diagram -> Chart -> Gain Offset Softkey help information
Press this softkey and turn V0 knob to adjust the gain deviation (dB).

Utility Key -> Potter Diagram -> Chart -> Phase Scale Softkey help information
Press this softkey and turn V0 knob to adjust the phase scale (degree).

Utility Key -> Potter Diagram -> Chart -> Phase Offset Softkey help information
Press this softkey and turn V0 knob to adjust the phase deviation (degree).

Utility Key -> Potter Diagram -> Chart -> Return Softkey help information
Press this softkey to return to the previous menu.



58

Threads

1253

Posts

1333

Credits

金牌会员

Rank: 6Rank: 6

Credits
1333
 Author| Post time 2021-1-14 08:31:24 | Show all posts
Utility Key -> Potter Diagram -> Run Softkey help information
Press this softkey to begin the frequency response test.

Utility Key -> Potter Diagram -> Run -> Cancel Softkey help information
Press this softkey to exit the frequency response test.

Utility Key -> Potter Diagram -> Press To Save Softkey help information
When the scope complete the frequency response test, press this softkey to open the File Manager Menu if a
USB storage device has been detected.

Utility Key -> Potter Diagram -> Press To Save -> New Softkey help information
Press this softkey to enter New File Menu and display the alpha-numeric keypad dialog.

Utility Key -> Potter Diagram -> Press To Save -> New -> Type Softkey help information
Select a file or a directory to create.

Utility Key -> Potter Diagram -> Press To Save -> New -> Switch To Softkey help information
Toggle between Name and Keypad.



58

Threads

1253

Posts

1333

Credits

金牌会员

Rank: 6Rank: 6

Credits
1333
 Author| Post time 2021-1-15 08:01:59 | Show all posts
Utility Key -> Potter Diagram -> Press To Save -> New -> Backspace Softkey help information
Deletes a character from the name each time before the cursor's left.

Utility Key -> Potter Diagram -> Press To Save -> New -> Delete Softkey help information
Clear all characters for the name.

Utility Key -> Potter Diagram -> Press To Save -> New -> Save Softkey help information
Create new a file or a directory on the USB storage device.

Utility Key -> Potter Diagram -> Press To Save -> New -> Return Softkey help information
Press this softkey to return to the previous menu.

Utility Key -> Potter Diagram -> Press To Save -> Delete Softkey help information
To remove the selected file.



You have to log in before you can reply Login | Register

Points Rules

Dark room|Mobile|Archiver|Electronic Engineer Discuss

2024-3-29 06:15 GMT+8 , Processed in 0.253778 second(s), 19 queries .

Powered by Discuz! X3.2

© 2001-2013 Comsenz Inc.

Quick Reply To Top Return to the list