MPO6002EDU Series Oscilloscope Guide

WisdomAugust

Utility Key -> Potter Diagram -> Press To Save -> Rename Softkey help information

Press this softkey to open File Rename Menu and display the alpha-numeric keypad dialog.

Utility Key -> Potter Diagram -> Press To Save -> Rename -> Switch To Softkey help information

Toggle between Name and Keypad.

Utility Key -> Potter Diagram -> Press To Save -> Rename -> Backspace Softkey help information

Deletes a character from the name each time before the cursor's left.

Utility Key -> Potter Diagram -> Press To Save -> Rename -> Delete Softkey help information

Clear all characters for the name.

Utility Key -> Potter Diagram -> Press To Save -> Rename -> Confirm Softkey help information

Rename the existing file.

Utility Key -> Potter Diagram -> Press To Save -> Rename -> Return Softkey help information

Press this softkey to return to the previous menu.

WisdomAugust

Utility Key -> Potter Diagram -> Press To Save -> Rename Softkey help information

To save a new csv format file with the default file name on the USB storage device.

Utility Key -> Potter Diagram -> Press To Save -> Return Softkey help information

Press this softkey to return to the previous menu.

Utility Key -> Search Softkey help information

Press to search through an acquisition for user defined events/criteria.

Cursors Key help information

Press the Cursors key to turn on or turn off the Cursors function.

Cursors measurement contains voltage and time on the scope signals, and timing on digital channels

(if the scope with digital channels).

The cursors allow you to get very accurate readings of either time (X-axes) or voltage (Y-axes) differences

between different parts of a waveform.

Turn the V0 knob to move the cursors’ position.

WisdomAugust

Cursors Key -> Mode Softkey help information

Press this softkey to toggle the cursors mode between manual and track.

Manual - X, Y, X-Y, 1/dX values are displayed. Adjust cursor positions by rotating the V0 knob.

Track - When you turn the V0 knob, as the X cursor moves, the corresponding Y cursor follows

the waveform assigned to the X source.

Cursors Key -> Mode Manual -> Source Softkey help information

Select the analog channel or math as the source on which the cursors will indicate measurements.

Cursors Key -> Mode Manual -> Y Softkey help information

Select the Y cursors, and use the V0 knob to adjust its position.

Y cursors are horizontal dashed lines that adjust vertically and normally indicate Volts. When math

functions are used as a source, the measurement units correspond to that math function.

Cursors Key -> Mode Manual -> X Softkey help information

Select the X cursors, and use the V0 knob to adjust its position.

X cursors are vertical dashed lines that adjust horizontally and normally indicate time relative to the

trigger point. When used with the FFT math function as a source, the X cursors indicate frequency.

Cursors Key -> Mode Manual -> X-Y Softkey help information

Select the X-Y cursors mode.

Push the V0 knob to change the selected cursor, and rotate the V0 knob to adjust the position.

WisdomAugust

Cursors Key -> Mode Manual -> Cursors Softkey help information

Press this softkey to make the selection of the cursor(s), and turn the V0 knob to adjust them.

The AX cursor (long-dashed-vertical line) and BX cursor (short-dashed vertical line) adjust

horizontally and indicate time relative to the trigger point for all sources except math FFT

(frequency is indicated).

AXBX Press this softkey to adjust the AX and BX cursors together by turning the V0 knob.

The BX - AX value will remain the same since the cursors adjust together.

You can adjust the X cursors together to check for pulse width variations in a pulse train.

The AY cursor (long-dashed horizontal line) and BY cursor (short-dashed horizontal line)

adjust vertically and indicate values relative to the waveform's ground point, except math

FFT where the values are relative to 0 dB.

AYBY Press this softkey to adjust the AY and BYcursors together by turning the V0 knob.

The BY - AY value will remain the same since the cursors adjust together.

WisdomAugust

Cursors Key -> Mode Track -> Source A Softkey help information

Select the analog channel or math as the source A to measure their waveform values.

Cursors Key -> Mode Track -> Source B Softkey help information

Select the analog channel or math as the source B to measure their waveform values.

Cursors Key -> Mode Track -> Cursors Softkey help information

Press this softkey to make the selection of the cursor(s), and turn the V0 knob to adjust them. When you

turn the V0 knob, as the X cursor moves, the corresponding Y cursor follows the waveform assigned to

the X source.

The AX cursor (long-dashed-vertical line) and BX cursor (short-dashed vertical line) adjust horizontally

and indicate time relative to the trigger point for all sources except math FFT (frequency is indicated).

AXBX Press this softkey to adjust the AX and BX cursors together by turning the V0 knob. The BX - AX

value will remain the same since the cursors adjust together.

WisdomAugust

Meas Key help information

When open the Measurements Menu by pressing the Meas key, you can:

*Make automatic measurements (up to 42 measurement parameters).

*Turn on or off statistic measurements.

*Enable or disable digital voltmeter.

Meas Key -> Source Softkey help information

Select the channel, math, or reference waveform as the source to make measurements.

Meas Key -> Type Softkey help information

Press this softkey to display the screen-based menu to select fully-automated measurements

like frequency, period, rise/fall time, etc.

WisdomAugust

Meas Key -> DVM Softkey help information

Press this softkey to open the Digital Voltmeter (DVM) Menu.

Meas Key -> DVM -> Enable Softkey help information

Enable or disable digital voltmeter.

Meas Key -> DVM -> Source Softkey help information

Press this softkey to select an analog channel waveform source for which you want to measure.

Meas Key -> DVM -> Type Softkey help information

Switch the digital voltmeter measurement type among DC RMS, AC RMS, and DC.

Meas Key -> DVM -> Return Softkey help information

Press this softkey to return to the previous menu.

WisdomAugust

Meas Key -> All Measure Softkey help information

Turn on or off all measure function.

Meas Key -> Statistics Softkey help information

Turn on or off measurement statistics for active measurements.

The statistics display information:

* Measurement name

* Currently measured value

* The average

* The maximum measured value

* The minimum measured value

* The standard deviation (RMSE)

* The number of times the measurement has been made (count)

Meas Key -> Clear All Softkey help information

Press this softkey to remove all measurements from the display.

WisdomAugust

Meas Key -> Settings Softkey help information

Press this softkey to display the Settings Menu to set up additional parameters for the selected measurement.

Meas Key -> Settings -> Type Softkey help information

Choose Delay (or Phase if available) as the selected measurement.

Meas Key -> Settings -> Source A Softkey help information

Press Source A softkey to select an analog channel for Delay (or Phase if available) measurement.

Meas Key -> Settings -> Source B Softkey help information

Press Source B softkey to select an analog channel for Delay (or Phase if available) measurement.

Meas Key -> Settings -> Return Softkey help information

Press this softkey to return to the previous menu.

WisdomAugust

Meas Key -> Gate Softkey help information

Press this softkey to enter the Gate Menu.

Meas Key -> Gate -> Gate On/Off Softkey help information

Press this softkey to turn on or off the gate measure function.

Meas Key -> Gate -> Gate On -> Cursor A Softkey help information

Press this softkey and use the V0 knob to adjust Cursor A position.

Meas Key -> Gate -> Gate On -> Cursor B Softkey help information

Press this softkey and use the V0 knob to adjust Cursor B position.

Meas Key -> Gate -> Gate On -> Cursor A-B Softkey help information

Press this softkey and use the V0 knob to adjust Cursor A and Cursor B positions together.

Meas Key -> Gate -> Return Softkey help information

Press this softkey to return to the previous menu.