MPO6002EDU Series Oscilloscope Guide

WisdomAugust

Wave Gen Key help information

Press the WaveGen key to open the Waveform Generator Menu (if the scope with built-in waveform generator).

*Select channels of the waveform generator.

*Turn on or off output on the front panel's Gen Out BNC.

*Set up the waveform generator's wave type, frequency, amplitude, offset, phase, impedance, modulation, and burst.

Wave Gen Key -> Waveform Softkey help information

Select the waveform generator output by pressing this softkey or turning the V0 knob.

The current waveforms can be output with Sine, Square, Ramp, Noise, Pulse, DC, Sinc, Exponential Fall,

Haversine, Lorentz, Dual Tone, Gauss, ECG, and Arbitrary waveforms.

WisdomAugust

Wave Gen Key -> Waveform -> Square -> Duty Softkey help information

Press this softkey to toggle between Duty and Duty Fine adjustment, and use the V0 knob to adjust the

duty cycle of the square waveform output. Settings range: 2% - 98%.

Wave Gen Key -> Waveform -> Ramp -> Symmetry Softkey help information

Press this softkey to toggle between Symmetry and Symmetry Fine adjustment, and use the V0 knob

to adjust the symmetry of the ramp waveform output. Symmetry applies optional symmetry modifications

to the wave shape.

Wave Gen Key -> Waveform -> Pulse -> Width Softkey help information

Press this softkey to toggle between Width and Width Fine adjustment, and use the V0 knob to adjust

the width of the pulse waveform output.

WisdomAugust

Wave Gen Key -> Waveform -> Pulse -> Leading/Trailing Softkey help information

Press this softkey to toggle between Leading edge (Fine) and Trailing edge (Fine) adjustment, and use

the V0 knob to adjust the edge times.

The edge times set the transition times for the leading and trailing edges of the pulse.

The device will adjust the edge time to accommodate the specified pulse width.

Wave Gen Key -> Waveform -> Arb 1/Arb 2/Arb 3/Arb 4 -> Recall Softkey help information

Press this softkey to display a screen-based file list if a USB storage device detected.

Turn the V0 knob to select an arbitrary waveform data file, press the V0 knob to load the arbitrary

waveform to the oscilloscope.

Wave Gen Key -> Source Softkey help information

Select the channel of the waveform generator.

WisdomAugust

Wave Gen Key -> Enable Softkey help information

Turn on or off output on the front panel's Gen Out BNC for the selected channel.

Wave Gen Key -> Frequency/Period Softkey help information

Press this softkey to switch between Frequency (Fine) and Period (Fine) adjustment, and use the V0 knob

to adjust the frequency or period of the waveform generator output.

Wave Gen Key -> Amplitude/High Level Softkey help information

Press this softkey to switch between Amplitude (Fine) and High Level (Fine) adjustment, and use the V0 knob

to adjust the amplitude or high level of the waveform generator output.

Wave Gen Key -> Offset/Low Level Softkey help information

Press this softkey to switch between Offset (Fine) and Low Level (Fine) adjustment, and use the V0 knob to

adjust the offset or low level of the waveform generator output.

WisdomAugust

Wave Gen Key -> Phase Softkey help information

Press this softkey to toggle between Phase and Phase Fine adjustment, and use the V0 knob to adjust

the phase of the waveform generator output.

Wave Gen Key -> Output Load Softkey help information

Set the output load impedance to high resistance or 50 ohms.

Wave Gen Key -> Align Phase Softkey help information

This softkey allows you to align the phases of the outputs and then adjust the phase of one of the channels

relative to the other.

Wave Gen Key -> Modulation Softkey help information

Press this softkey to activate the Waveform Generator Modulation Menu.

Modulation is where an original carrier waveform is modified according to the amplitude of a second

modulation waveform.

The modulation type (AM, FM, PM, or PWM) specifies how the carrier waveform is modified.

WisdomAugust

Wave Gen Key -> Modulation -> Modulation On/Off Softkey help information

Turn on or off modulated waveform generator output.

Wave Gen Key -> Modulation -> Type Softkey help information

Select the modulation type.

AM (Amplitude Modulation) - the amplitude of the carrier wave is changed according to the amplitude

of the modulating signal.

FM (Frequency Modulation) - the frequency of the carrier wave is changed in line with the amplitude

of the modulating signal.

PM (Phase Modulation) - the phase of the carrier wave is changed according to the amplitude of the

modulating signal.

PWM (Pulse Width Modulation) - the width of the pulse of the carrier wave is changed in line with

the modulating signal.

WisdomAugust

Wave Gen Key -> Modulation -> Waveform Softkey help information

Switch the shape of the modulating waveform among Sine, Square, and Ramp.

Wave Gen Key -> Modulation -> Frequency Softkey help information

Press this softkey to toggle between Frequency and Frequency Fine adjustment, and use the V0 knob

to adjust the frequency of the modulating waveform.

Wave Gen Key -> Modulation -> Depth/Deviation Softkey help information

Press this softkey to toggle between Depth (Deviation) and Depth Fine (Deviation Fine) adjustment,

and use the V0 knob to specify.

In AM schemes, the modulation depth refers to the amplitude ratio of the modulating signal to the carrier

signal. At 0% depth, the amplitude is one-half of the carrier’s amplitude setting. At 100% depth, the

amplitude varies according to the modulating waveform, from 0% to 100% of the carrier’s amplitude.

AM depth range: 0% to 120%.

In FM schemes, the frequency deviation setting represents the peak variation in frequency of the modulated

waveform from the carrier frequency.

The carrier frequency must always be greater than or equal to the frequency deviation.

The carrier frequency plus the deviation cannot exceed the selected function's maximum frequency plus

100 kHz.

In PM schemes, the phase deviation setting represents the peak variation in phase of the modulated

waveform from the carrier waveform. The phase deviation can be set from 0 to 350 degrees.

Wave Gen Key -> Modulation -> Return Softkey help information

Press this softkey to return to the previous menu.

WisdomAugust

Wave Gen Key -> Burst Softkey help information

To open the Waveform Generator Burst Menu.

Burst allows a specific number of waveforms to be output before outputting zero.

Wave Gen Key -> Burst -> Burst On/Off Softkey help information

The device can output a waveform for a specified number of cycles, called a burst.

Press this softkey to turn on or off burst waveform generator output.

Wave Gen Key -> Burst -> Count Softkey help information

Set the number of cycles (1 to 2,000,000,000) to be output per burst. Burst count can be used in the

triggered burst mode only.

WisdomAugust

Wave Gen Key -> Burst -> Source Softkey help information

Select the burst trigger source from manual, Pass/Fail and DSO Trigger.

Manual - The device outputs a waveform of the specified number of cycles (burst count) when a trigger

is received by pressing the Trigger softkey. After the specified number of cycles has been output, the

device stops and waits for the next trigger.

Pass/Fail - the device initiates one burst each time a pass/fail trigger is received.

When do pass/fail test, turn on output, and select output to DDS, the corresponding waveform generator

source will switch to Pass/Fail Trigger Source automatically, and the default count is 1.

DSO Trigger - The device outputs one burst of the specified number of cycles each time the oscilloscope

waveform triggered.

Wave Gen Key -> Burst -> Trigger Softkey help information

When Manual Source selected, the device outputs a burst by pressing this softkey.

Wave Gen Key -> Burst -> Return Softkey help information

Press this softkey to return to the previous menu.

WisdomAugust

Save/Recall Key -> Save Softkey help information

Press this softkey to open the Save Menu.

Save/Recall Key -> Save -> Type Softkey help information

Keep pressing this softkey or use the V0 knob to select a file type: Setup, Waveform, Reference Waveform,

and CSV.

Save/Recall Key -> Save -> Type -> Ref -> Source Softkey help information

Press this softkey to select the waveform source to be saved as a reference waveform file.

Save/Recall Key -> Save -> Save To Softkey help information

Toggle between internal and external to save the file.