Please select To the mobile version | Continue to access the desktop computer version

Electronic Engineer Discuss

Author: WisdomAugust

How to Use the Modulated Waveform Function of HDG6000B?

[Copy link]

52

Threads

835

Posts

915

Credits

高级会员

Rank: 4

Credits
915
 Author| Post time 2019-11-8 11:54:39 | Show all posts
2 Select PWM.
Press Mod key, select type as PWM.
3 Set the width deviation.
Press the Deviation softkey and set the value to 20% using the numeric keypad or the knob and cursor
keys.
4 Set the modulating frequency.
Press the PWM Freq softkey and then set the value to 5 Hz using the numeric keypad or the knob and
cursor keys.
5 Select the modulating waveform shape.
Press the Shape softkey to select the shape of the modulating waveform.
For this example, select a sine wave.


At this point, the function generator outputs a PWM waveform with the specified modulation parameters
(if the output is enabled).


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

52

Threads

835

Posts

915

Credits

高级会员

Rank: 4

Credits
915
 Author| Post time 2019-11-9 08:05:46 | Show all posts
6 View the waveform.
Of course, to really view the PWM waveform, you would need to output it to an oscilloscope. If you do this,
you will see how the duty cycle deviation varies, in this case, from 0% to 50%. At a modulation frequency
of 5 Hz, the deviation is quite visible.



This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

52

Threads

835

Posts

915

Credits

高级会员

Rank: 4

Credits
915
 Author| Post time 2019-11-11 08:21:27 | Show all posts
Amplitude Modulation (AM)
A modulated waveform consists of a carrier waveform and a modulating waveform. In AM, the amplitude
of the carrier is varied by the instantaneous voltage of the modulating waveform. The function generator
will accept an internal or external modulation source.
To Select AM Modulation
? The function generator will allow only one modulation mode to be enabled at a time. For example, you
cannot enable AM and FM at the same time. When you enable AM, the previous modulation mode is
turned off.
? The function generator will not allow AM to be enabled at the same time that sweep or burst is enabled.
When you enable AM, the sweep or burst mode is turned off.


52

Threads

835

Posts

915

Credits

高级会员

Rank: 4

Credits
915
 Author| Post time 2019-11-12 08:59:43 | Show all posts
? Front-Panel Operation: You must enable AM before setting up any of the other modulation parameters.
Press Mod key and then select “AM” using the Type softkey. The AM waveform is output using the
present settings for the carrier frequency, modulating frequency, output amplitude, and offset voltage.



This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

52

Threads

835

Posts

915

Credits

高级会员

Rank: 4

Credits
915
 Author| Post time 2019-11-13 09:11:14 | Show all posts
Carrier Waveform Shape
? AM carrier shape: Sine, Square, Ramp, Pulse, Arbitrary or Harmonic waveform. The default is Sine.
You cannot use noise, or dc as the carrier waveform.



This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

52

Threads

835

Posts

915

Credits

高级会员

Rank: 4

Credits
915
 Author| Post time 2019-11-14 09:15:49 | Show all posts
? Front-Panel Operation: Press any of the front-panel function keys except Noise. For arbitrary waveforms,
press Arb and then choose the Select Type softkey to select the active waveform.


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

52

Threads

835

Posts

915

Credits

高级会员

Rank: 4

Credits
915
 Author| Post time 2019-11-15 08:05:12 | Show all posts
Carrier Frequency
The maximum carrier frequency depends on the function selected as shown below. The default is 1 kHz
for all functions.

Function
Minimum Frequency
Maximum Frequency
Sine
Square
Ramp
Pulse
Arbs
1μHz
1μHz
1μHz
1μHz
1μHz
200MHz
60MHz
5MHz
50MHz
50MHz

? Front-Panel Operation: To set the carrier frequency, press the Freq softkey for the selected function.
Then use the knob or numeric keypad to enter the desired frequency.


52

Threads

835

Posts

915

Credits

高级会员

Rank: 4

Credits
915
 Author| Post time 2019-11-18 08:25:22 | Show all posts
Modulating Waveform Shape
The function generator will accept an internal or external modulation source for AM.
? Modulating waveform shape (internal source): Sine, Square, Ramp, Noise, or Arb waveforms (Sinc, Exp Fall, Haver Sine, Lorentz, Gause, Dual Tone, ECG). The default is Sine.
? Sine


When modulating waveform shape is Sine, display on the generator.


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

52

Threads

835

Posts

915

Credits

高级会员

Rank: 4

Credits
915
 Author| Post time 2019-11-19 08:16:32 | Show all posts


When modulating waveform shape is Sine, display on the oscilloscope.


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

52

Threads

835

Posts

915

Credits

高级会员

Rank: 4

Credits
915
 Author| Post time 2019-11-20 08:08:09 | Show all posts
Edited by WisdomAugust at 2019-12-5 09:54

? Noise
When modulating waveform shape is Noise, display on the generator.



This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x
You have to log in before you can reply Login | Register

Points Rules

Dark room|Mobile|Archiver|Electronic Engineer Discuss

2021-7-30 21:47 GMT+8 , Processed in 0.203569 second(s), 19 queries .

Powered by Discuz! X3.2

© 2001-2013 Comsenz Inc.

Quick Reply To Top Return to the list