Please select To the mobile version | Continue to access the desktop computer version

Electronic Engineer Discuss

Author: WisdomAugust

How to Use the Burst Function of HDG6000B?

[Copy link]

52

Threads

835

Posts

915

Credits

高级会员

Rank: 4

Credits
915
 Author| Post time 2019-8-5 08:06:41 | Show all posts
Produce a burst using ramp.


The Ramp key light when using ramp wave.


Burst display on generator when using ramp wave.


Display on oscilloscope when using ramp wave.


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

52

Threads

835

Posts

915

Credits

高级会员

Rank: 4

Credits
915
 Author| Post time 2019-8-6 09:03:02 | Show all posts
Produce a burst using pulse

The Pulse key light when using pulse wave.

Burst display on the generator when using pulse wave.


Display on an oscilloscope when using pulse wave.


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

52

Threads

835

Posts

915

Credits

高级会员

Rank: 4

Credits
915
 Author| Post time 2019-8-7 10:23:46 | Show all posts
Produce a burst using harmonic.



The Harmonic key light when using harmonic wave.

Burst display on generator when using harmonic wave.

Display on oscilloscope when using harmonic wave.


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

52

Threads

835

Posts

915

Credits

高级会员

Rank: 4

Credits
915
 Author| Post time 2019-8-8 10:17:50 | Show all posts
Produce a burst using arbitrary waveform.


The Arb key light when using arbitrary wave.


Burst display on generator when using arbitrary wave.

Display on oscilloscope when using arbitrary wave.


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

52

Threads

835

Posts

915

Credits

高级会员

Rank: 4

Credits
915
 Author| Post time 2019-8-9 12:00:21 | Show all posts
To Select Burst
Press Burst key to output a burst using the present settings for frequency, output amplitude, and offset voltage. (the backlight of the key goes on)
Note:
A. The function generator will not allow burst to be enabled at the same time that sweep or any modulation mode is enabled. When you enable burst, the sweep or modulation mode is turned off.
B. You must enable burst before setting up any of the other burst parameters.


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

52

Threads

835

Posts

915

Credits

高级会员

Rank: 4

Credits
915
 Author| Post time 2019-8-12 07:58:09 | Show all posts
Burst Type


You can use burst in one of three modes as described below. The function generator enables one burst
mode at a time based on the trigger source and burst source that you select (see the table below).






This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

52

Threads

835

Posts

915

Credits

高级会员

Rank: 4

Credits
915
 Author| Post time 2019-8-13 13:25:55 | Show all posts
N Cycle Burst (Triggered Burst Mode)
In this mode (default), the function generator outputs a waveform with a specified number of cycles
(burst count) each time a trigger is received. After the specified number of cycles have been output,
the function generator stops and waits for the next trigger. You can configure the function generator
to use an internal trigger to initiate the burst or you can provide an external trigger by applying a trigger
signal to the front-panel Sync/Mod/Trig connector, or sending an internal trigger command manually
by pressing the front-panel Trigger key.


N Cycle Burst (Internal Trigger)


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

52

Threads

835

Posts

915

Credits

高级会员

Rank: 4

Credits
915
 Author| Post time 2019-8-14 16:16:21 | Show all posts
Infinite Cycle Burst (Triggered Burst Mode)
In this mode , the function generator outputs continuous waveforms with a infinite number of cycles
after receiving trigger signal. You can configure the function generator to use an external trigger by
applying a trigger signal to the front-panel Sync/Mod/Trig connector, or sending an trigger command
manually by pressing the front-panel Trigger key.


Infinite Cycle Burst


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

52

Threads

835

Posts

915

Credits

高级会员

Rank: 4

Credits
915
 Author| Post time 2019-8-15 13:18:10 | Show all posts
Gated Burst ( External Gated Burst Mode)
In this mode, the output waveform is either “on” or “off ” based on the level of the external signal applied
to the front-panel Sync/Mod/Trig connector. When the gate signal is true, the function generator outputs
a continuous waveform. When the gate signal goes false, the current waveform cycle is completed and
then the function generator stops while remaining at the voltage level corresponding to the starting burst
phase of the selected waveform. For a noise waveform, the output stops immediately when the gate signal
goes false.


Gated Burst


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

52

Threads

835

Posts

915

Credits

高级会员

Rank: 4

Credits
915
 Author| Post time 2019-8-16 11:08:43 | Show all posts
Gated Burst
When the gated mode is selected, the burst count, burst period, and trigger source are ignored (these
parameters are used for the triggered burst mode only). If a manual trigger is received, it is ignored and
no error will be generated.
When the gated mode is selected, you can also select the polarity of the signal on the front-panel
Sync/Mod/Trig connector.
Front-Panel Operation: After enabling bursts, press the N Cycle (triggered), Inf Cycle or Gate softkey.
To select the polarity of the external gate signal on the Sync/Mod/Trig connector, press the Polarity
softkey. The default polarity is Positive.



This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x
You have to log in before you can reply Login | Register

Points Rules

Dark room|Mobile|Archiver|Electronic Engineer Discuss

2021-7-30 22:36 GMT+8 , Processed in 0.200922 second(s), 19 queries .

Powered by Discuz! X3.2

© 2001-2013 Comsenz Inc.

Quick Reply To Top Return to the list