Please select To the mobile version | Continue to access the desktop computer version

Electronic Engineer Discuss

View: 24177|Reply: 41

How to Use the Burst Function of HDG6000B?

[Copy link]

58

Threads

1253

Posts

1333

Credits

金牌会员

Rank: 6Rank: 6

Credits
1333
Post time 2019-7-6 08:22:23 | Show all posts |Read mode
How to Use the Burst Function of HDG6000B?
HDG6000B can output a waveform for a specified number of cycles, called a burst.



This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x
Reply

Use magic Report

58

Threads

1253

Posts

1333

Credits

金牌会员

Rank: 6Rank: 6

Credits
1333
 Author| Post time 2019-7-8 09:29:39 | Show all posts
To Output a Burst
You can output the burst at a rate determined by the internal rate generator or the signal level on the
front-panel Sync/Mod/Trig connector. For this example, you will output a three-cycle sine wave with
a 10 ms burst period. You will not change the other parameters from their default settings: internal
burst source and 0 degree starting phase.



This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

58

Threads

1253

Posts

1333

Credits

金牌会员

Rank: 6Rank: 6

Credits
1333
 Author| Post time 2019-7-11 08:00:31 | Show all posts
Edited by WisdomAugust at 2019-7-11 08:04

1 Select the function and amplitude of the burst.
For burst waveforms, you can select sine, square, ramp, pulse, or arbitrary waveforms (noise is allowed
only in the “gated” burst mode and dc is not allowed). For this example, select a sine wave with an
amplitude of 200mV.


2 Select the burst mode.

Press and then verify that the “N Cycle” (internally-triggered) mode is currently selected.file:///C:\Users\ADMINI~1\AppData\Local\Temp\ksohtml5012\wps1.jpg

This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

58

Threads

1253

Posts

1333

Credits

金牌会员

Rank: 6Rank: 6

Credits
1333
 Author| Post time 2019-7-12 08:06:41 | Show all posts
3 Set the burst count.
Press the countsoftkey and then set the count to “3” using the numeric keypad or knob.


4 Set the burst period.
Press the period softkey and then set the period to 10 ms using the numeric keypad or the knob and cursor
keys. The burst period sets the time from the start of one burst to the start of the next burst.


At this point, the function generator outputs a continuous three-cycle burst (if the output is enabled).


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

58

Threads

1253

Posts

1333

Credits

金牌会员

Rank: 6Rank: 6

Credits
1333
 Author| Post time 2019-7-15 08:14:11 | Show all posts
5 View the waveform.
To view the waveform parameters.


Note:
A. You can generate a single burst (with the specified count) by pressing the Trigger key.
B. You can also use an external gate signal to either turn the burst signal “on” or “off” based on the
external signal applied to the front-panel Sync/Mod/Trig connector.


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

58

Threads

1253

Posts

1333

Credits

金牌会员

Rank: 6Rank: 6

Credits
1333
 Author| Post time 2019-7-16 09:52:31 | Show all posts
To Trigger a Burst
You can issue triggers from the front panel for bursts using a manual trigger or an internal trigger.
? Internal triggering is enabled with the default settings of the function generator. In this mode, the
function generator outputs continuously when the burst mode is selected.
? Manual triggering initiates one burst each time you press theTrigger key from the front-panel.
Continue pressing this key to re-trigger the function generator.
Generator display when using a manual trigger


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

58

Threads

1253

Posts

1333

Credits

金牌会员

Rank: 6Rank: 6

Credits
1333
 Author| Post time 2019-7-17 11:36:37 | Show all posts
Oscillscope display when using a manual trigger



? The Trigger key is disabled when a function other than burst is currently selected (or when
the output is disabled). A message


pop up in display when using a manual trigger.


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

58

Threads

1253

Posts

1333

Credits

金牌会员

Rank: 6Rank: 6

Credits
1333
 Author| Post time 2019-7-18 08:12:20 | Show all posts
Burst Mode
You can configure the function generator to output a waveform with a specified number of cycles, called
a burst. The function generator can produce a burst using sine, square, ramp, pulse, harmonic or arbitrary
waveforms (noise is allowed only in the gated burst mode and dc is not allowed).
Produce a burst using sine.


The Sine key light when using sine wave.


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

58

Threads

1253

Posts

1333

Credits

金牌会员

Rank: 6Rank: 6

Credits
1333
 Author| Post time 2019-8-1 08:13:34 | Show all posts
Burst display on the generator when using sine wave.




Display on the oscilloscope when using sine wave.



This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

58

Threads

1253

Posts

1333

Credits

金牌会员

Rank: 6Rank: 6

Credits
1333
 Author| Post time 2019-8-3 13:31:41 | Show all posts
Produce a burst using square.


The Square key light when using a square wave.

Burst display on the generator when using square wave.


Display on an oscilloscope when using square wave.


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x
You have to log in before you can reply Login | Register

Points Rules

Dark room|Mobile|Archiver|Electronic Engineer Discuss

2024-3-28 20:12 GMT+8 , Processed in 0.179549 second(s), 22 queries .

Powered by Discuz! X3.2

© 2001-2013 Comsenz Inc.

Quick Reply To Top Return to the list