Electronic Engineer Discuss
Title: HandHeld Oscilloscope Software [Print this page]
Author: WisdomAugust Time: 2018-7-13 16:14
Title: HandHeld Oscilloscope Software
Install and Uninstall
This section describes how to install the handheld oscilloscope software on your computer.
DSO1000S is a software application that provides computer control and data
collection from Hantek handheld oscilloscopes, including the DSO1062S,
DSO1122S, DSO1152S, and DSO1202S product families. Before using
DSO1000S, you need to know the configuration requirements and installation
procedures of the software.
System Requirements
Before using DSO1000S Software, ensure that your computer meets the
following configuration requirements.
Hardware Configuration Requirements
● 1GHz or higher processor
● 200M or more hard disk space
● 1024x768 monitor resolution or above
● 256M or more RAM
● USB or LAN interface and cable
Running Environment
● Microsoft Windows XP, 2000, Win7, 8, 10 (32bit and 64bit)
Author: WisdomAugust Time: 2018-7-16 14:42
To install handheld oscilloscope, follow these steps:
? Insert the installation disk into the CD-ROM drive.
? Open the install file “DSO1000S” [attach]2188[/attach]→ “Set up” [attach]2189[/attach].
? Double click “Setup. Exe” to start the installation wizard. See figure 1.
[attach]2190[/attach]
Author: WisdomAugust Time: 2018-7-17 08:42
? The Welcome to DSO1000S Setup program dialog box appears.
See Figure 2.
[attach]2191[/attach]
Figure 2
? Read the information in the dialog box, and click “Next” to pop up the
“Destination Location” dialogue box (See Figure 3).
[attach]2192[/attach]
Figure 3
Author: WisdomAugust Time: 2018-7-18 08:43
Select the installation folder, click “Next” to accept the default location or click
“Browse” to select other folder ( See Figure 4).
[attach]2193[/attach]
Figure 4
? The Confirm Installation dialog box appears (See figure 5) and click “Next”.
[attach]2194[/attach]
Figure 5
Author: WisdomAugust Time: 2018-7-19 08:28
? Installing DSO1000S (See Figure 6)
[attach]2195[/attach]
Figure 6
After all the files have been installed, the installation complete and click
“Finish”. (See Figure 7)
[attach]2196[/attach]
Figure 7
Author: WisdomAugust Time: 2018-7-20 09:08
If you connect DSO1000S software to the oscilloscope by USB interface,
you need to install USB driver. The USB driver installed auotomatically.
. Connect the oscilloscope (now you should make sure the oscilloscope is
working) to your computer using the included USB cable.
[attach]2199[/attach]
Figure 8
[attach]2200[/attach]
Figure 9
Author: WisdomAugust Time: 2018-7-21 09:43
Uninstall
After you install the software, you can find “DSO1000S Ver 2.0.0.7” from the
“Programs and Features” in the Microsoft Windows Control Panel and click
“Remove” See figure 10.
[attach]2204[/attach]
Author: WisdomAugust Time: 2018-7-23 08:43
Edited by WisdomAugust at 2018-7-23 08:44
1.2Software Interface
[attach]2205[/attach]
file:///C:\Users\ADMINI~1\AppData\Local\Temp\ksohtml\wps83B1.tmp.pngfile:///C:\Users\ADMINI~1\AppData\Local\Temp\ksohtml\wps83B2.tmp.pngfile:///C:\Users\ADMINI~1\AppData\Local\Temp\ksohtml\wps83B3.tmp.png
1. Menu bar
2. Toolbar
3. Link state indicator
4. Data, graph display area
5. Base Control Panel
6. Status bar
Author: WisdomAugust Time: 2018-8-8 14:16
Edited by WisdomAugust at 2018-8-8 14:17
1.1.1 Menu Bar
[attach]2209[/attach]
Figure 12
File
[attach]2210[/attach]
Figure 13
Author: WisdomAugust Time: 2018-8-9 08:14
Edited by WisdomAugust at 2018-8-9 08:16
- New
Create a new display windows. Window types include Analyse Bus, Arithmetic, Power Spectrum,
Waveform Measurement, Waveform Tabular, and YT Sheet. (These windows can be created repeatedly).
[attach]2211[/attach]
Figure 14
Author: WisdomAugust Time: 2018-8-10 15:59
- Open
Open the data file. The extensions are *.wfm - waveform window (YT Sheet), *.mes - measurement window (Waveform Measurement), *.dat - acquisition window (Waveform Tabular), *.mth - math window (Arithmetic), *.psm - spectrum window (Power Spectrum), *. Bus - bus analysis window (Analyse Bus).
[attach]2213[/attach]
Figure 15
Author: WisdomAugust Time: 2018-8-13 09:42
- Close
Close the current window.
- Open Workspace
Open the workspace (extension *.wrk).
[attach]2222[/attach]
Figure 16
Author: WisdomAugust Time: 2018-8-14 10:25
- Save Workspace
Save the current workspace.
[attach]2223[/attach]
Figure 17
- Save Workspace As
Save the current workspace with a new file name.
[attach]2224[/attach]
Figure 18
Author: WisdomAugust Time: 2018-8-15 08:35
Edited by WisdomAugust at 2018-8-15 10:51
- Close Workspace
Close the current workspace.
[attach]2225[/attach]
Figure 19
- Save
Save the current window with the specified path and file name.
[attach]2226[/attach]
Figure 20
- Save As
Save the current window with a new file name.
- Export
Export files (waveform window and bus analysis window can be exported as bmp files, measurement window and acquisition window can be exported as txt file and CSV file).
[attach]2227[/attach]
Figure 21
- Open Set File
Open the settings file (extension *.set).
[attach]2226[/attach]
Figure 22
Author: WisdomAugust Time: 2018-8-16 09:38
- Save Set File
Save the settings of the file.
Figure 23
- Print
Print the contents of the current window.
[attach]2232[/attach]
Figure 24
- Print Preview
Preview the to be printed contents of the current window.
[attach]2233[/attach]
Figure 25
- Print Setup
Setup print options.
[attach]2234[/attach]
Figure 26
- Exit
Exit the program.
[attach]2235[/attach]
Figure 27
Author: WisdomAugust Time: 2018-8-17 09:21
View
[attach]2236[/attach]
Figure 28
- Tool Bar
Show the hidden toolbar
- Status Bar
Show the hidden status bar.
- Control Window
Show the hidden control window.
- Full Screen
Make the waveform window full screen. (Note: This will only be available when the current window is "Waveform Window")
Author: WisdomAugust Time: 2018-8-20 12:45
Tools
[attach]2238[/attach]
Figure 29
- Connect to Oscilloscope
When working windows disconnect to the oscilloscope device, press it to connect the device to computer, and the indicator in green [attach]2239[/attach].
- Disconnect
Press this key to disconnect the oscilloscope device from computer, and the indicator in red [attach]2240[/attach].
- Options
Setup the communication parameters and program parameters.
[attach]2241[/attach]
Figure 30
Author: WisdomAugust Time: 2018-8-21 09:20
Window
[attach]2243[/attach]
Figure 31
- Cascade
The windows are displayed in a cascade.
[attach]2244[/attach]
Figure 32
- Tile
Tile each window.
[attach]2245[/attach]
Figure 33
- Arrange Icons
Arrange display the minimize windows.
[attach]2246[/attach]
Figure 34
When click the window name under the Arrange Icons, the window will display on the working area.
[attach]2247[/attach]
Figure 35
Author: WisdomAugust Time: 2018-8-23 09:31
Help
[attach]2248[/attach]
Figure 36
- Contents
Display the help file.
- About Scope
Show the scope version data.
[attach]2249[/attach]
Figure 37
Author: WisdomAugust Time: 2018-8-24 08:20
Toolbar
[attach]2250[/attach]
Figure 38
1. New
Create a new display windows. Window types include Analyse Bus, Arithmetic, Power Spectrum, Waveform Measurement, Waveform Tabular, and YT Sheet. See Figure 14.
2. Open the Workspace
Open the workspace (extension *.wrk). See Figure 16.
3. Open the data file
Open the data file (extensions are *.wfm - waveform window, *.mes - measurement window, *.dat - acquisition window, *.mth - math window, *.psm - spectrum window, *.bus - bus analysis window). See Figure 15.
4. Open the settings file
Open the settings file (extension *.set). See Figure 22.
5. Save Workspace
Save the workspace file. See Figure 17.
6. Save data file
Save the data file.
7. Save the settings file
Save the settings file.
8. Export
Export files (waveform documents and bus analysis documents can export bmp files, measurement documents and acquisition documents can export txt files and CSV files).
9. Cut
10. Copy
11. Paste
12. Print
Prints the contents of the current window. See Figure 24.
13. Establish a connection
Connect your PC to your oscilloscope.
14. Disconnect
Disconnect the connection between the PC and the oscilloscope.
15. Options
You can set communication parameters and program parameters. See Figure 30.
16. About
Open the About dialog box. See Figure 37.
17. When the indicator is connected, the indicator turns green; when the connection is disconnected, the indicator turns red.
Author: WisdomAugust Time: 2018-9-4 08:15
Control Window
[attach]2251[/attach]
Figure 39
The control window includes a tree directory and a shortcut menu.
The tree directory lists the settings, controls, and virtual panel of the device.
Click the "+" in front of the item to expand the item to see all the items that belong to the item.
Click the "-" in front of the item to shrink the item and hide all children belonging to the item.
Note: The lowest level of the sub-item is generally used to execute commands or set parameters.
Connecting different models of oscilloscopes, the control window will display different models. This description uses the word “oscilloscope” instead.
Update Parameters
If the PC and the oscilloscope are connected, the software will update the parameters in the setup file to the oscilloscope after opening the setup file.
Shortcut Menu
You can pop up the shortcut menu by clicking the right mouse button, which is available in the control window.
Save Set File: Save the settings of the file.
Author: WisdomAugust Time: 2018-9-5 08:14
Edited by WisdomAugust at 2018-9-7 11:12
Waveforms
[attach]2252[/attach]
Figure 40
Number | | | |
| | | Channel 1 waveform is not visible See Figure 41 |
| Channel 1 waveform is visible See Figure 42 |
| | | Channel 2 waveform is not visible See Figure 43 |
| Channel 2 waveform is visible See Figure 42 |
| | | Math waveform is not visible See Figure 44 |
| Math waveform is visible See Figure 42 |
Author: WisdomAugust Time: 2018-9-7 11:23
When Channel 1 eye icon in gray.
[attach]2253[/attach]
Figure 41
When Channel 1, Channel 2 and Math eye icon in black.
[attach]2254[/attach]
Figure 42
When Channel 2 eye icon in gray.
[attach]2255[/attach]
Figure 43
When Math eye icon in gray.
[attach]2256[/attach]
Figure 44
Author: WisdomAugust Time: 2018-9-10 08:24
Display
[attach]2265[/attach]
Figure 45
Number | | | |
| | | The oscilloscope switches to YT mode display |
| The oscilloscope switches to XY mode display |
| | | Oscilloscope persistence time is automatic |
0.2S, 0.4S, 0.8S, 1S, 2S, 4S, 8S | Oscilloscope persistence time is 0.2, 0.4, 0.8, 1, 2, 4, 8 seconds |
| Oscilloscope persistence time is infinite |
| | | Display the connection line between the sampling points of the oscilloscope |
| Display sampling points on the screen |
| | | Set up the display brightness of the oscilloscope |
| | | The oscilloscope grid appears as a dotted line |
| The oscilloscope grid is displayed as a solid line |
| Oscilloscope does not display grid |
| | | Set up the grid brightness of the oscilloscope |
Author: WisdomAugust Time: 2018-9-11 09:31
-Format
Double click “Format”, format setup dialogue popout. You may switch the oscilloscope display format between YT and XY.
[attach]2266[/attach]
Figure 46
YT Display
[attach]2269[/attach]
Figure 47
XY Display
[attach]2270[/attach]
Figure 48
Author: WisdomAugust Time: 2018-9-12 10:46
-Persistence
Double click “Persistence”, persistence setup dialogue pop out. You may set the oscilloscope persistence time.
[attach]2271[/attach]
Figure 49
Note: When select “Auto”, the persistence is closed.
You may setup the persistence time among 0.2S, 0.4S, 0.8S, 1S, 2S, 4S, 8S and infinite.
E. g setup the persistence @ 1S, the oscilloscope display as figure 50.
[attach]2272[/attach]
Figure 50
Author: WisdomAugust Time: 2018-9-13 08:32
-Style
Double click “Style”, style setup dialogue pop out.You may switch the oscilloscope display line between vectors and dots.
[attach]2273[/attach]
Figure 51
Author: WisdomAugust Time: 2018-9-15 08:14
-Contrast
Double click “Contrast”, constrast setup dialoguepop out. You may setup the oscilloscope display contrast from 0 to 15.
[attach]2274[/attach]
Figure 52
When set contrast @ 0.
[attach]2275[/attach]
Figure 53
When set contrast @ 15.
[attach]2276[/attach]
Figure 54
Author: WisdomAugust Time: 2018-9-21 14:34
-Grid Type
Double click “Grid Type”, grid type setup dialogue pop out. You may setup the oscilloscope grid to dashed, real line, or close.
[attach]2279[/attach]
Figure 55
Dashed Grid
[attach]2280[/attach]
Figure 56
Real line grid
[attach]2281[/attach]
Figure 57
When close grid
[attach]2282[/attach]
Figure 58
Author: WisdomAugust Time: 2018-9-21 14:37
-Grid Brightness
Double click “Grid Brightness”, grid brightness setup dialogue pop out. You may setup the oscilloscope grid brightness from 0 to 15.
[attach]2283[/attach]
Figure 59
When set contrast @ 0.
[attach]2284[/attach]
Figure 60
When set contrast @ 15.
[attach]2285[/attach]
Figure 61
Author: WisdomAugust Time: 2018-9-25 08:57
Acquire
[attach]2287[/attach]
Figure 62
Number | | | |
| | | The oscilloscope acquisition type is real-time acquisition |
| The oscilloscope acquisition type is equivalent acquisition |
| | | The oscilloscope acquisition mode is sampling |
| Oscilloscope acquisition mode is peak |
| The oscilloscope acquisition mode is average |
| | | |
| | | Set the oscilloscope's memory depth to 4k~1M |
Author: WisdomAugust Time: 2018-9-25 08:59
-Type
Double click “Type”, acquisition type setup dialogue pop out. You may setup the oscilloscope between real time and equivalent time.
[attach]2288[/attach]
Figure 63
-Mode
Double click “Mode”, acquisition mode setup dialogue pop out. You may setup the oscilloscope among sample, peak detect and average.
[attach]2289[/attach]
Figure 64
-Store Capacity
Double click “Store Capacity”, store capacity setup dialogue pop out. You may setup the oscilloscope memory depth amond 4K, 40K, 512K and 1M.
[attach]2290[/attach]
Figure 65
Author: WisdomAugust Time: 2018-9-27 08:01
Vertical
[attach]2292[/attach]
Figure 66
Number | | | |
| | | Turn on channel waveform display |
| Turn off channel waveform display |
| | | Turn off the bandwidth limitation |
| Turn on the bandwidth limitation to 20MHz |
| | | |
| |
| |
| | -2V～2V (2mv/div ≤Volt/Div≤ 200mv/div) | Set the vertical position of the channel waveform (in div) |
-50V～50V (200mv/div<Volt/Div ≤5v/div) |
| | | Select the value of Volt/Div from 2mv to 50v |
| | | Set the appropriate probe attenuation factor to make the base reading correct |
|
|
|
| | | |
| |
| Welcome to Electronic Engineer Discuss (https://www.eediscuss.com/) |
Powered by Discuz! X3.2 |