Electronic Engineer Discuss

Title: Hantek 2c42 nao liga apois interrup??o da atualiza?ao do firmware Socorro [Print this page]

Author: elison Time: 2020-8-12 02:50
Title: Hantek 2c42 nao liga apois interrup??o da atualiza?ao do firmware Socorro

Olá, tenho um 2c42 e no início da atualiza??o do firmware meu PC travou e reiniciei.
O osciloscópio agora n?o liga, quando eu o conecto ao PC o bot?o liga / desliga permanece ligado e se eu remover as baterias e reconectar o bot?o liga / desliga ele fica piscando.
Existe uma maneira de recuperar o osciloscópio ??
Ajuda por favor !!

Author: amy Time: 2020-8-15 09:23
Please download the latest software and install in this link:
http://hantek.com.cn/products/detail/13174

Run the software and select Help->CheckUpdate.
Select "Rescue" and follow the prompts to operate.

[attach]3787[/attach]

Author: elison Time: 2020-8-16 03:00

amy replied at 2020-8-15 09:23
Please download the latest software and install in this link:
http://hantek.com.cn/products/detail/1 ...

Hello, I have a 2c42 and at the beginning of the firmware update my PC crashed and restarted.
The oscilloscope now does not turn on, when I connect it to the PC the on / off button remains on and if I remove the batteries and reconnect the on / off button it is flashing.
Is there a way to recover the oscilloscope ?? I was also reading some posts that use a usb adapter module ttl rs232 pl2303 hx how do I do this step by step and what files do I use? I took a look at this dolink video https://www.youtube.com/watch?v=-uF2fdVxx1E
Help please !!

Author: elison Time: 2020-8-16 03:03

amy replied at 2020-8-15 09:23
Please download the latest software and install in this link:
http://hantek.com.cn/products/detail/1 ...

I already did it does not work because the oscilloscope is no longer being recognized by the USB port
what would arm1 and arm2 be?
have any whatsaap contact for support or email?
Hello, I have a 2c42 and at the beginning of the firmware update my PC crashed and restarted.
The oscilloscope now does not turn on, when I connect it to the PC the on / off button remains on and if I remove the batteries and reconnect the on / off button it is flashing.
Is there a way to recover the oscilloscope ?? I was also reading some posts that use a usb adapter module ttl rs232 pl2303 hx how do I do this step by step and what files do I use? I took a look at this dolink video https://www.youtube.com/watch?v=-uF2fdVxx1E
Help please !!

Author: tol47 Time: 2020-8-16 18:51
Edited by tol47 at 2020-8-16 19:37

elison replied at 2020-8-16 03:03
I already did it does not work because the oscilloscope is no longer being recognized by the USB ...

You need a full STM32 dump (not .dfu !!!) taken from another HANTEK 2C42 (2D42, 2C72) with the same display !!! how about you. Go to the forum forum.nickbel.com. Everything is there. Power on USB-TTL adapter set 3V3!!!

Author: amy Time: 2020-8-17 16:56

elison replied at 2020-8-16 03:03
I already did it does not work because the oscilloscope is no longer being recognized by the USB ...

I have sent an email to you, please check.

Author: elison Time: 2020-8-17 21:19

tol47 replied at 2020-8-16 18:51
You need a full STM32 dump (not .dfu !!!) taken from another HANTEK 2C42 (2D42, 2C72) with the same ...

https://produto.mercadolivre.com.br/MLB-1140989965-pl2303hx-pl2303-hx-conversor-usb-cabo-p-ttl-rs232-arduino-_JM

Esse serve?

Author: elison Time: 2020-8-17 21:29

tol47 replied at 2020-8-16 18:51
You need a full STM32 dump (not .dfu !!!) taken from another HANTEK 2C42 (2D42, 2C72) with the same ...

https://produto.mercadolivre.com.br/MLB-1140989965-pl2303hx-pl2303-hx-conversor-usb-cabo-p-ttl-rs232-arduino-_JM

this will do? it has 5v and 3v3 output

Author: elison Time: 2020-8-17 23:40

elison replied at 2020-8-16 03:03
I already did it does not work because the oscilloscope is no longer being recognized by the USB ...

I got the files but I have doubts
in arm1 says that
Does the VCC not need to be connected? because? in the forum they said it only worked with the connected VCC and the RX AND TX SHOULD BE NORMAL OR REVERSE CONNECTED?

Author: elison Time: 2020-8-18 00:07
Edited by elison at 2020-8-18 00:18

amy replied at 2020-8-17 16:56
I have sent an email to you, please check.

I received your email, but I have the following questions:in arm1 says thatDoes the VCC not need to be connected? Why? in the forum they said it only worked with the connected VCC.and about the RX AND TX MUST BE NORMAL OR REVERSE CONNECTEDhttps://produto.mercadolivre.com.br/MLB-1140989965-pl2303hx-pl2303-hx-conversor-usb-cabo-p-ttl-rs232-arduino-_JM?quantity=1

the adapter ai that link will serve? claims to be 3.3v ttl level and has 5v and 3.3v output

Author: tol47 Time: 2020-8-18 03:52

elison replied at 2020-8-17 21:19
https://produto.mercadolivre.com.br/MLB-1140989965-pl2303hx-pl2303-hx-conversor-usb-cabo-p-ttl-rs2 ...

Rx converter to Tx HANTEK, Tx converter to Rx HANTEK. POWER SUPPLY CAN BE CONNECTED FROM USB Cable from PC. Jumper on TTL converter-3v3!!!

Author: tol47 Time: 2020-8-18 03:59
Edited by tol47 at 2020-8-18 04:05

CHECK THE LEVELS TTL-ONLY 3V3!!! NOT 5V!!! connection Rx, Tx-reverse. Power- USB cable from PC.

Author: elison Time: 2020-8-18 07:32

tol47 replied at 2020-8-18 03:59
CHECK THE LEVELS TTL-ONLY 3V3!!! NOT 5V!!! connection Rx, Tx-reverse. Power- USB cable from PC.

how do i check the ttl level? to measure by the multimeter? because the adapter is this link ai I don't know for sure because it says that it has 3.3v and 5v output and also says ttl 3.3v level

Author: elison Time: 2020-8-20 02:55

tol47 replied at 2020-8-18 03:59
CHECK THE LEVELS TTL-ONLY 3V3!!! NOT 5V!!! connection Rx, Tx-reverse. Power- USB cable from PC.

a big doubt I am about the adapter: R $ 3.22 5% OFF | 1pcs PL2303 USB To RS232 TTL Converter Adapter Module
https://a.aliexpress.com/_mLev2h9

it has 5 output pins 5v and 3.3v Tx and Rx and Gnd but what would be the ttl level? can I use this adapter there from the link taking the 3.3v adapter and put in the oscilloscope vcc
but the final doubt is about the tx and rx have some max tension that these can withstand? will be that the tx and rx of that adapter there is compatible with the oscilloscope? in the description it says that it is ttl 3.3v and 5v levels beste if this adapter has automatic tx and dx voltage? can I use this adapter on the oscilloscope 2c42?

Author: tol47 Time: 2020-8-20 18:49
Edited by tol47 at 2020-8-20 18:59

The best -ST-Link v.2. It is specially designed for STM.

Author: elison Time: 2020-9-28 09:48

Segui os passos do arm1 que ame passou e gra?as a Deus deu tudo certo e osciloscopio voltou a ligar e funcionar normalmente

Author: elison Time: 2020-9-28 09:51
Segui os passos do arm1 que ame passou e gra?as a Deus deu tudo certo e osciloscopio voltou a ligar e funcionar normalmente. Obrigado a todos

Author: elison Time: 2021-3-1 09:05

amy replied at 2020-8-17 16:56
I have sent an email to you, please check.

Olá eu consegui ressuscitar o meu osciloscópio Hantek 2c42 seguindo os passos que você mandou, porém ele agora está com o sistema do Hantek 2c82 como fazer pra deixa ele com o software normal do hanteck 2c42

Hello I managed to resuscitate my Hantek 2c42 oscilloscope following the steps you sent, but now it is with the Hantek 2c82 system how to make it leave with the normal hanteck 2c42 software

Welcome to Electronic Engineer Discuss (https://www.eediscuss.com/)