Electronic Engineer Discuss

Title: Hantek6254BC IIC (I2C) decoding [Print this page]

Author: Matti Time: 2020-6-8 14:31
Title: Hantek6254BC IIC (I2C) decoding
Edited by Matti at 2020-6-8 14:39

Hantek6254BC, how do I get the IIC (I2C) message decoding to work?
Software Version: 20160528
Driver Version: 20160531
FPGA Version: D001
PCB Version: V1.08
Product SN: 64C08135

Author: wangshuang Time: 2020-6-9 15:54
Please contact me with email, file is too large to upload here.
My address: wangshuang@hantek.com

Author: KeenAmateur Time: 2020-6-27 18:29
What file at what version was provided to solve this issue?
Is it FPGA image from D001 > F004 or something else?

Author: wangshuang Time: 2020-6-30 09:49

KeenAmateur replied at 2020-6-27 18:29
What file at what version was provided to solve this issue?
Is it FPGA image from D001 > F004 or som ...

Please refer to this post to update the FPGA.
https://www.eediscuss.com/forum. ... id=15193&extra=

Author: QMESAR Time: 2020-7-17 21:46
Hi Hantek Team.
I have an 6254BD is it possible to have IIC decoding ? if I understand this post correctly if I do the FPGA update it should work or am I wrong
Thank you for your attention

Author: wangshuang Time: 2020-7-20 14:40

QMESAR replied at 2020-7-17 21:46
Hi Hantek Team.
I have an 6254BD is it possible to have IIC decoding ? if I understand this post cor ...

Same for 6254BD.

Author: QMESAR Time: 2020-7-21 13:32
Hi.
Thank you for the information,
Questions
(1) If I do the FPGA update where in the PC Software do I select Serial/IIC decoding ?
(2) is SW V2.2.6 the latest Verion doesit support the IIC decoding

Thank you

Author: QMESAR Time: 2020-7-21 15:34
Edited by QMESAR at 2020-7-21 15:37

I would expect the I2C to be under the Trigger setup but with me there is nothing,
I have successfully done the FPGA upgrade

Author: wangshuang Time: 2020-7-22 08:39

QMESAR replied at 2020-7-21 15:34
I would expect the I2C to be under the Trigger setup but with me there is nothing,
I have successful ...

Please download the latest software to try again.
http://hantek.com.cn/products/detail/10164

Author: QMESAR Time: 2020-7-22 09:50
Hi.

I did install the latest version of the SW before I did the upgrade ,I just did a new download from your link and installed the SW again No IIC option

Please help Thank you
[attach]3738[/attach]

Author: KeenAmateur Time: 2020-7-22 17:27
Hi

The trigger for serial decoding only appears on the RHS of display in trigger node, trigger drop down, it does not appear in drop down menu options. See picture.
Hope this helps.

Author: wangshuang Time: 2020-7-22 18:19

KeenAmateur replied at 2020-7-22 17:27
Hi

The trigger for serial decoding only appears on the RHS of display in trigger node, trigger drop ...

You can directly select the decoding function in the list above. The decoding function was added later and did not appear in the trigger setup. It should be a bug. I will report it to the engineer for modification. Currently you can use it normally.

Author: QMESAR Time: 2020-7-22 20:35
Hi Guys ,

A big thank you to both of you, I found it and happy this was something that was always missing in the HANTEK scopes now it is there
Great Stuff

Author: QMESAR Time: 2020-7-24 00:11

It should be a bug. I will report it to the engineer for modification.

Please be so kind and inform us on this thread when you have modified the Software that the Serial decoders are also shown in the main trigger window

Thank you very much

Author: wangshuang Time: 2020-7-28 10:01

QMESAR replied at 2020-7-24 00:11
Please be so kind and inform us on this thread when you have modified the Software that the Seria ...

ok, I will.

Author: QMESAR Time: 2020-8-18 16:09
Hi Team
Any update on this !

Regards

Welcome to Electronic Engineer Discuss (https://www.eediscuss.com/)