Electronic Engineer Discuss

Title: Hantek 2000 boot logo [Print this page]

Author: uncle_sem Time: 2019-11-6 23:52
Title: Hantek 2000 boot logo
Hello! There is a "boot logo on/off" in menu, but currently boot logo is a black screen, i guess - or it's look like a black screen. So, is it possible to change it to something else?

Author: Han Time: 2019-11-7 14:50
You can use upper software to change it.

Author: uncle_sem Time: 2019-11-8 18:04
sorry, don't get it - which software is it? hantek2000_software.zip?

Author: uncle_sem Time: 2019-11-8 19:09
found it! but is it possible to use some picture , not just a few text lines?

Author: amy Time: 2019-11-11 16:28
Sorry, cannot add picture as boot screen.

Author: mostorer Time: 2020-4-21 16:06

uncle_sem replied at 2019-11-8 19:09
found it! but is it possible to use some picture , not just a few text lines?

Hi there. May I kindly ask you what the software to be used is ?

Author: OASJ2YSeeEhBQo1 Time: 2020-4-22 08:02

mostorer replied at 2020-4-21 16:06
Hi there. May I kindly ask you what the software to be used is ?

Just use the software that came with the device. Go to the menu Utility -> SetBanner

You can write a text message for each line and it will show on the screen of the oscilloscope during its startup. Nothing very useful really.

Author: any1ne Time: 2020-4-24 08:51

OASJ2YSeeEhBQo1 replied at 2020-4-22 08:02
Just use the software that came with the device. Go to the menu Utility -> SetBanner

You can writ ...

Not working.
[attach]3539[/attach]

Author: OASJ2YSeeEhBQo1 Time: 2020-4-24 13:06

any1ne replied at 2020-4-24 08:51
Not working.

Which version are you using of FW, FPGA and PC software?

The message is saying to update your firmware, have you tried that? I just tried here and it works.

Author: mostorer Time: 2020-4-24 14:08

OASJ2YSeeEhBQo1 replied at 2020-4-24 13:06
Which version are you using of FW, FPGA and PC software?

The message is saying to update your fir ...

Yes, I can confirm. It happened the same to me.

It asked me to update Arm2. Then I did the update and finally it worked.
I would have create a small logo/picture using ASCII ART, but only 15 chars per line with no monospaced font.

Author: any1ne Time: 2020-4-25 12:38

OASJ2YSeeEhBQo1 replied at 2020-4-24 13:06
Which version are you using of FW, FPGA and PC software?

The message is saying to update your fir ...

firmware 2019110801 and FPGA 04. Is this the latest version?

Author: OASJ2YSeeEhBQo1 Time: 2020-4-28 12:31

any1ne replied at 2020-4-25 12:38
firmware 2019110801 and FPGA 04. Is this the latest version?

Yes, this is the same version that I use. What's your software version? I'm using v1.1.11

Author: amy Time: 2020-5-25 14:19
Please scan the QR code on the back of the oscilloscope to download the latest software and install, and now use the "Help->Checkupdate" to update the firmware.

Welcome to Electronic Engineer Discuss (https://www.eediscuss.com/)