Electronic Engineer Discuss
Title: DSO5202B firmware updates fail with 0xfe [Print this page]
Author: dgScope Time: 2019-5-16 08:28
Title: DSO5202B firmware updates fail with 0xfe
Edited by dgScope at 2019-5-18 04:50
I’ve tried upgrading the firmware on my DSO5202B using the files below, and both resulted in 0xfe errors (no update file found).
dso5kb_func_dso5202b20140610.up
dso5kb_func_dso5202b20180226.up
These firmware files were obtained from the Hantek website and the Hantek OneDrive account.
I tried multiple FAT32-formatted 1GB USB flash drives. The flash drives are otherwise operational with the scope. I can save waveforms and screenshots to USB ok. I've reformatted so the only file present is the firmware up file. No luck.
Any help would be appreciated.
Scope S/N: T 1G/200M 033099
SW version: 2.06.3 (130814.1)
HW version: 0x555583e9
Thanks
Author: amy Time: 2019-5-18 13:23
Sir, your scope is too old, the new firmware is not suitable for it.
Please send a message to our email support@hantek.com
Author: dgScope Time: 2019-5-21 05:16
I did follow up with support@hantek.com and haven't received a response.
My question to Support is: What’s the highest supported firmware version for the DSO5202B with hardware version (0x555583e9)?
Thanks.
Author: amy Time: 2019-5-25 16:28
Edited by amy at 2020-2-14 10:02
Sir, the linux version of your scope is 2.06.3. The latest firmware is not suitable for it.
Please use this firmware to update.
[attach]2900[/attach]
Attention, if the firmware version number earlier than 2013, such as 120505.0 or 120825.0, please do not upgrade with this firmware.
Author: Slash200 Time: 2020-2-4 03:54
Dear Amy,
I have the same problem.
Model: DSO5202B
SW: 2.06.3.(130425.0)
HW: 10070x555583e9
I can't update from the downloads from the hantek page.
Also your attached update shows me the error 0xfe
Can you please help me updating my DSO?
Thank you!
regards
Author: amy Time: 2020-2-14 09:58
Sir, You can upgrade with the above firmware.
Author: cdidier Time: 2020-3-10 01:22
Hello Amy,
I have the same problem too. But my firmware is quite older:
Model: DSO5202B
SW: 2.06.3(120808.0)
HW: 10070x555583e9
What is the procedure to update my device?
Author: amy Time: 2020-3-13 16:33
Sorry, there is no upgrade firmware suitable for your oscilloscope.
Author: JSP40 Time: 2020-5-1 15:59
I have the same problem.
DSO5202P
Firmware update failed error 0xfe
No upgrade files detected on USB device
Author: BeanieBob Time: 2020-5-3 21:40
I had this problem before with files not visible.
I suspect the USB partition cannot be mounted because the drive capacity is too large.
I was able to use an old 512MB USB stick successfully.
Can you try with a small capacity USB drive - or possibly create a small partition
if you do not have an older USB stick. Hope it works for you.
( I am not from Hantek - just a user - so this is not official advice)
Author: JSP40 Time: 2020-5-3 23:37
my oscilloscope can use the usb, read and record graphics on it. the usb format is correct in my case
Author: ying Time: 2020-5-6 13:26
Please press "Utility->System Information" button and send us a screenshot to study.
Author: JSP40 Time: 2020-5-7 14:10
Hi this is my system information window:
model: DSO5202P
sw vversion: 3.40.0(180120.0)
hw version: 1010xffff8108
serial number: T 1G/138 044564
boot count: 55
upgrade count: 0
lcd.front.ts: 3.3.0
Author: dg:Scope Time: 2020-7-14 19:50
Is there any newer firmware than 2.06.3(140924.0) for DSO5202B running 2.06.3 Linux? (Newer than the attached zip?)
Thanks.
Author: wangshuang Time: 2020-7-15 08:42
Please get the latest firmware in Hantek official website:
http://hantek.com.cn/products/detail/3
Author: gustavosmk Time: 2021-3-9 03:17
Hello Amy,
I have the same problem too. But my firmware is quite older:
Model DSO5202B
soft version 2.05.0
hard version 0x555583e8
Author: aruschel Time: 2021-4-5 22:27
My friend, I had the same problem and decided to change the pendrive, put a different brand that is certainly the problem. Follow a link in Spanish explaining well what I said above.
https://www.youtube.com/watch?v=qXLTHLb961Q
Author: aruschel Time: 2021-4-5 22:28
My friends, I had the same problem and decided to change the pendrive, put a different brand that is certainly the problem. Follow a link in Spanish explaining well what I said above.
https://www.youtube.com/watch?v=qXLTHLb961Q
Author: aruschel Time: 2021-4-5 22:30
My friend, I had the same problem and decided to change the pendrive, put a different brand that is certainly the problem. Follow a link in Spanish explaining well what I said above.
https://www.youtube.com/watch?v=qXLTHLb961Q
| Welcome to Electronic Engineer Discuss (https://www.eediscuss.com/) |
Powered by Discuz! X3.2 |