Hantek 2c42 nao liga apois interrup??o da atualiza?ao do firmware Socorro
Olá, tenho um 2c42 e no início da atualiza??o do firmware meu PC travou e reiniciei.
O osciloscópio agora n?o liga, quando eu o conecto ao PC o bot?o liga / desliga permanece ligado e se eu remover as baterias e reconectar o bot?o liga / desliga ele fica piscando.
Existe uma maneira de recuperar o osciloscópio ??
Ajuda por favor !!
Please download the latest software and install in this link:
http://hantek.com.cn/products/detail/13174
Run the software and select Help->CheckUpdate.
Select "Rescue" and follow the prompts to operate.
amy replied at 2020-8-15 09:23
Please download the latest software and install in this link:
http://hantek.com.cn/products/detail/1 ...
Hello, I have a 2c42 and at the beginning of the firmware update my PC crashed and restarted.
The oscilloscope now does not turn on, when I connect it to the PC the on / off button remains on and if I remove the batteries and reconnect the on / off button it is flashing.
Is there a way to recover the oscilloscope ?? I was also reading some posts that use a usb adapter module ttl rs232 pl2303 hx how do I do this step by step and what files do I use? I took a look at this dolink video https://www.youtube.com/watch?v=-uF2fdVxx1E
Help please !!
amy replied at 2020-8-15 09:23
Please download the latest software and install in this link:
http://hantek.com.cn/products/detail/1 ...
I already did it does not work because the oscilloscope is no longer being recognized by the USB port
what would arm1 and arm2 be?
have any whatsaap contact for support or email?
Hello, I have a 2c42 and at the beginning of the firmware update my PC crashed and restarted.
The oscilloscope now does not turn on, when I connect it to the PC the on / off button remains on and if I remove the batteries and reconnect the on / off button it is flashing.
Is there a way to recover the oscilloscope ?? I was also reading some posts that use a usb adapter module ttl rs232 pl2303 hx how do I do this step by step and what files do I use? I took a look at this dolink video https://www.youtube.com/watch?v=-uF2fdVxx1E
Help please !!
Edited by tol47 at 2020-8-16 19:37
elison replied at 2020-8-16 03:03
I already did it does not work because the oscilloscope is no longer being recognized by the USB...
You need a full STM32 dump (not .dfu !!!) taken from another HANTEK 2C42 (2D42, 2C72) with the same display !!! how about you. Go to the forum forum.nickbel.com. Everything is there. Power on USB-TTL adapter set 3V3!!!
elison replied at 2020-8-16 03:03
I already did it does not work because the oscilloscope is no longer being recognized by the USB...
I have sent an email to you, please check.
tol47 replied at 2020-8-16 18:51
You need a full STM32 dump (not .dfu !!!) taken from another HANTEK 2C42 (2D42, 2C72) with the same ...
https://produto.mercadolivre.com.br/MLB-1140989965-pl2303hx-pl2303-hx-conversor-usb-cabo-p-ttl-rs232-arduino-_JM
Esse serve?
tol47 replied at 2020-8-16 18:51
You need a full STM32 dump (not .dfu !!!) taken from another HANTEK 2C42 (2D42, 2C72) with the same ...
https://produto.mercadolivre.com.br/MLB-1140989965-pl2303hx-pl2303-hx-conversor-usb-cabo-p-ttl-rs232-arduino-_JM
this will do? it has 5v and 3v3 output
elison replied at 2020-8-16 03:03
I already did it does not work because the oscilloscope is no longer being recognized by the USB...
I got the files but I have doubts
in arm1 says that
Does the VCC not need to be connected? because? in the forum they said it only worked with the connected VCC and the RX AND TX SHOULD BE NORMAL OR REVERSE CONNECTED?
Edited by elison at 2020-8-18 00:18
amy replied at 2020-8-17 16:56
I have sent an email to you, please check.
I received your email, but I have the following questions:in arm1 says thatDoes the VCC not need to be connected? Why? in the forum they said it only worked with the connected VCC.and about the RX AND TX MUST BE NORMAL OR REVERSE CONNECTEDhttps://produto.mercadolivre.com.br/MLB-1140989965-pl2303hx-pl2303-hx-conversor-usb-cabo-p-ttl-rs232-arduino-_JM?quantity=1
the adapter ai that link will serve? claims to be 3.3v ttl level and has 5v and 3.3v output
Pages:
[1]
2